43045-0614 Specs & Footprint: 3.0mm Pitch Data Brief

7 February 2026 138
43045-0614 3.0mm Pitch Connector Specifications

3.0mm-pitch wire-to-board connectors account for a large share of mid-power interconnects in consumer and industrial electronics. This is due to their compact size and a typical per-contact capability in the 5–8.5 A range. This brief decodes the 43045-0614 spec set and provides practical PCB footprint and layout guidance for a 2x3 header.

Product Overview

Connector Role & Configuration

The 43045-0614 is a 2x3 vertical header in a 3.0mm pitch grid. While vertical PTH (Plated Through-Hole) is often chosen for mechanical robustness, right-angle and SMT variants cater to low-profile and automated assembly needs.

Operating Envelope

Typical Limits

Verified operating ranges include temperatures from −40°C to +105°C. Environmental ratings like flammability and glow-wire compliance must be cross-referenced with the official datasheet for specific end-use environments.

Key Electrical & Mechanical Specs

Electrical Parameters

Current per Contact 5A - 8.5A
  • ⚡ Voltage Rating: Verify per DC class
  • 🛡️ Insulation Resistance: Measured in MΩ
  • 🔄 Mating Cycles: Dependent on plating finish

Mechanical Dimensions

Pitch: 3.0mm Grid: 2x3 Style: Vertical PTH/SMT

Pull all dimensions (length, width, height, and pin shape) from official drawings. Tolerances are critical for solder fillet geometry and enclosure clearance.

Footprint & PCB Layout Guidance

Recommended Footprint Elements

Base the CAD footprint on a 3.0mm x 3.0mm grid:

  • PTH Drills: 0.9mm–1.2mm range with a minimum 0.25mm annular ring.
  • SMT Pads: Typical lengths of 1.2–1.8mm; widths of 0.7–1.0mm.
  • Paste Mask: 60–80% coverage to control solder volume.

Note: Always import the vendor STEP model into the PCB mechanical layer to verify enclosure fits and keepout distances.

Variants & Selection Criteria

Variant Type Core Trade-off Optimal Use Case
Vertical PTH (Tin) High retention, lower cost Mechanical robustness & wave soldering
SMT Vertical (Tin/Gold) Automated placement Reflow lines & tight Z-height constraints
Right-Angle PTH (Gold) Profile control & corrosion resistance Board-to-panel mating in harsh environments

Practical Design & Test Checklist

  • ✔ Confirm exact part variant and datasheet version before layout.
  • ✔ Download 3D STEP models for mechanical interference checks.
  • ✔ Run DRC with specific annular ring and creepage rules.
  • ✔ Validate thermal derating under actual expected load profiles.

Summary

The 43045-0614 is a compact 2x3 3.0mm-pitch header suited for mid-power wire-to-board connections where reliability is paramount. Key design decisions focus on footprint accuracy, mechanical support, and thermal management.

Power: 5-8.5A capability per contact.
Pitch: Precise 3.0mm x 3.0mm grid.
Robust: Multiple termination & plating options.

Frequently Asked Questions

How should I verify the 43045-0614 current rating? +
Confirm the max current per contact on the official datasheet and check test conditions. Perform in-circuit thermal tests on a prototype board to validate derating at your specific duty cycle and ambient conditions.
What footprint drill size is recommended for PTH pins? +
Typical drill guidance is 0.9–1.2mm depending on pin diameter and board house capabilities. Ensure you maintain at least a 0.25mm annular ring for reliable solder joints.
When is SMT preferred over PTH for this part? +
Choose SMT for automated reflow lines, lower profiles, and moderate mechanical loads. For high retention requirements or frequent mating cycles, PTH remains the more robust choice.