47745-0100 CMC 28-Pin Header: Full Specs & Test Data

7 February 2026 125

Bench tests reveal critical insertion/extraction cycles and contact resistance ranges, underpinning its role in high-reliability circuit boards. This comprehensive guide provides electrical and mechanical specifications, validated test data, and essential pre-production checklists for engineers and QA professionals.

Product Overview & Key Specifications

47745-0100 CMC 28-Pin Header Technical Overview

CMC 28-Pin Header Form Factor & Role

The 47745-0100 is a 28-position right-angle PCB plug featuring a single-row form factor designed for mixed power and signal applications. This component utilizes a standard 2.54 mm pitch and a 2.9 mm nominal tail length, perfectly aligning with common industrial board footprints. Engineers prioritize this design when edge space is constrained but high-density signal integration is required within a compact connector body.

Specification Typical Value / Technical Note
Contacts 28 positions, single row configuration
Pitch 2.54 mm (0.100")
Tail Length 2.9 mm nominal
Housing Material High-temperature Thermoplastic (Polyester), UL 94 V-0
Contact Plating Brass substrate, selective tin plating on mating area
Operating Temperature -40°C to +105°C

Mechanical & Dimensional Analysis

Detailed Dimensions & Mounting Features

Critical dimensions directly impact footprint accuracy, solder fillet quality, and mechanical retention. The 2.54 mm pitch results in an overall header length of approximately 69.5 mm. During PCB layout, designers should implement a 0.1 mm pad tolerance and 0.5 mm solder mask clearance. Incorporating locating features in the Gerber files ensures precise mechanical alignment during high-speed reflow or wave soldering processes.

Materials & Environmental Durability

The UL 94 V-0 polyester housing paired with brass contacts offers a balance of solderability and corrosion resistance. While tin plating is robust for standard embedded electronics, applications subject to high vibration or extreme thermal cycling should undergo verification for fretting and plating wear.

Electrical Performance & Signal Integrity

Current Rating Per Pin

1.5A — 3.0A

Application dependent: Recommend 25-40% derating for dense bundles.

Contact Resistance

10 — 30 mΩ

Initial value. Pass criteria typically set at ≤50 mΩ post-assembly.

Signal Integrity Considerations

Dense 28-pin headers can introduce crosstalk and skew. At a 2.54 mm pitch, near-end crosstalk (NEXT) may increase for signals in the MHz range. It is advised to route differential pairs away from power pins and maintain a clearance of 3× the trace width to preserve signal integrity.

Validation Procedures & Test Data

Bench Test Setup

  • • 4-Wire Kelvin measurements for high-precision resistance logging.
  • • Linear actuator fixtures to maintain consistent insertion/extraction force.
  • • Thermal cycling from -40°C to +105°C with stabilized soak times.

Target Metrics

Results should be averaged over n≥10 samples:

Insertion Force: Within ±15% of nominal
Resistance Drift: Thermal Rise (ΔT):

Common Failure Modes & Troubleshooting

Mechanical Degradation

Caused by improper insertion angles or excessive mating force. Symptoms include intermittent connectivity and visible plating abrasion. Mitigation: Use mechanical guides and specify selective gold plating for high-cycle requirements.

Assembly-Related Issues

Cold joints due to aggressive reflow profiles or insufficient tail protrusion. Mitigation: Verify tail length (2.9 mm) against PCB thickness and qualify the reflow profile using sample solder runs.

Pre-Production Selection & QA Checklist

✔ Footprint Verification: Confirm 2.54 mm pitch and hole tolerances.
✔ Plating Selection: Match tin or gold to environmental cycles.
✔ Solderability: Perform first-article inspection on solder fillets.
✔ Electrical Margin: Apply 25%+ current derating for safety.

Key Summary

  • ◆ Form Factor: Early layout must account for 2.54 mm pitch and ~2.9 mm tail length for process compatibility.
  • ◆ Electrical Integrity: Maintain contact resistance below 50 mΩ and derate current for high ambient temperatures.
  • ◆ Validation: Execute thermal cycling (-40 to +105 °C) and mechanical life tests to prevent field failures.
  • ◆ QA Protocol: Use sample solder runs and insertion-force checks to finalize production sign-off.

Frequently Asked Questions

How does the CMC 28-pin header affect PCB footprint planning? +
The header requires precise pad placement for a 2.54 mm pitch and specific solder fillet areas for 2.9 mm tails. Designers should include 0.1 mm pad tolerances and solder mask relief. Utilizing locating pegs in the layout helps prevent rotation during reflow.
What test methods are recommended for verifying contact resistance? +
A 4-wire Kelvin measurement is essential to eliminate lead resistance. Testing should involve a fixed mechanical fixture to ensure consistent alignment and a protocol of 100–500 insertion cycles to monitor resistance drift over time.
Which failures are most likely in the field and how are they mitigated? +
Common failures include mechanical wear, plating abrasion, and solder joint fatigue. These are mitigated by specifying high-quality plating for high-cycle use, optimizing reflow profiles, and implementing mechanical strain relief for environments with high vibration.