501876-1240 Header Spec Report: Complete Pin & Rating

4 February 2026 109

A compact, serviceable connector for dense PCB assemblies featuring a 12-position, 2.00 mm pitch, 2-row right-angle through-hole design. This report delivers practical mechanical calls-to-note, electrical limits, and layout rules for high-density engineering designs.

Quick Product Background & Headline Specs

Physical Configuration & Mechanical Dimensions

Point: Key physical parameters must be captured verbatim from the datasheet to avoid footprint errors.

Evidence: 12 circuits, 2 rows, 2.00 mm pitch, right-angle orientation, and 3.20 mm tail length.

Explanation: Copy exact pad-to-pad pitch and tail centerline dimensions into mechanical drawings. Annotate hole diameter, finished plating spec, and tail protrusion on the assembly drawing.

501876-1240 Header Spec Report: Complete Pin & Rating

Electrical Ratings & Environmental Limits

Point: Designers require both continuous and absolute maximum electrical values.

Evidence: Typical ratings are ~2 A per pin and 250 V; operating temperature range spans from -25°C to 85°C.

Explanation: Call out measurement conditions (ambient temp, humidity) when quoting current/voltage. Specify derating rules to reduce allowable continuous current as ambient temperature rises.

Current Rating (Per Pin) 2.0 Amperes
Temperature Range -25°C to +85°C

Pin Configuration & Layout Impact

Pinout & PCB Footprint Implications

Point: A 2.00 mm pitch, 12-pin layout constrains routing density and component placement.

Evidence: Narrow pitch reduces available route per layer and limits via placement near pads.

Design Rules:
  • Minimum keepout: 2.00 mm from tall components.
  • Drill clearance: Datasheet hole + 0.15 mm.
  • Annular ring: ≥ 0.25 mm.
  • Pad diameter: 1.3–1.5 mm for 0.8–1.0 mm hole.

Thermal Considerations & Derating

Point: Rated 2 A per pin must be contextualized for multi-pin and ambient conditions.

Evidence: Parallel pins can share current, but heating concentrates at contact and PCB tails.

Explanation: Derate per-pin current by thermal modeling. Target no more than 60% of lab-rated current in sustained elevated ambient conditions. Use copper pours tied to tails and perform temperature-rise tests.

Design, Assembly & Verification Guide

Assembly & Soldering Guidance

Footprint choices and solder-fill rules significantly affect assembly yield and mechanical strength. Right-angle through-hole tails impose cantilever stresses for edge-mated boards.

  • ✔ Wave solder: Recommend non-solder-filled tails and defined lead protrusion.
  • ✔ Selective/Hand solder: Specify solder-fill vs. non-fill explicitly.
  • ✔ DFM: Verify pad-to-edge clearance and mechanical interference.

Verification Test Plan

A concise, repeatable verification plan reduces field failures. Critical thresholds must be documented for lifecycle validation.

Test Category Criteria
Electrical Contact Resistance ≤ Limit
Mechanical Insertion Force within Spec
Environmental No continuity loss via vibration

Application Examples & Layout Best Practices

High-Density Signal Headers

Excels where board space is constrained. Right-angle mating reduces stack height. Best practice: Reserve one routing layer adjacent to the header for escape routing and maintain mating clearance.

Mixed Signal & Power Handling

Requires deliberate segregation. Segregate power pins to one row, place decoupling caps near entry points, and route signal traces with ground plane shielding to mitigate EMI.

Spec Sheet Checklist & Procurement Tips

Field Requirement / Value
Part Number 501876-1240
Pitch / Rows 2.00 mm / 2-Row (12 Position)
Termination Right-Angle Through-Hole (3.20 mm Tail)
Ratings 2 A / 250 V; -25°C to 85°C
Packaging Tray (Inspection for ESD & Orientation required)

* Procurement Tip: Sample contact resistance per lot (e.g., 5 pcs/lot) and define alternate families for supply disruptions.

Summary

  • ● Core mechanical highlights: 12 positions, 2-row, 2.00 mm pitch, right-angle through-hole with 3.20 mm tails. Ensure footprints match these dimensions exactly in all documentation.
  • ● Electrical and thermal constraints: Rated ~2 A per pin at 250 V. Always implement derating rules and thermal mitigation (copper pours, vias) in high-ambient environments.
  • ● Design and verification actions: Follow footprint pad/drill guidance, execute temperature-rise and contact-resistance tests, and document pass/fail criteria for production lot acceptance.

Frequently Asked Questions

What is the pitch and position count of the 501876-1240?
The 501876-1240 is a 12-position, 2-row header with a 2.00 mm pitch. Use the exact pitch and pin-count values from the datasheet when creating PCB footprints to ensure pad alignment and correct drill sizing.
How should an engineer derate current for the 501876-1240 under higher ambient temperatures?
Derate per-pin continuous current as ambient rises; a conservative rule is to limit sustained current to ~60% of the rated 2 A per pin in elevated ambient scenarios. Validate with thermal soak tests and contact-resistance monitoring to set production limits.
What key fields should be included in a BOM line for 501876-1240?
Include: full part number (501876-1240), positions, pitch, row count, orientation, termination type, tail length, plating finish, current/voltage ratings, operating temperature, and packaging. Add a mandatory reference to the datasheet for dimensional tolerances.